View AOZ6135HI_7736583.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

rev. 1.1 april 2010 www.aosmd.com page 1 of 11 aoz6135 high performance, low r on , 1 ? spdt analog switch general description the aoz6135 is a high performance single-pole double-throw (spdt), low power, ttl-compatible bus switch. the aoz6135 can handle analog and digital signals. signals with voltages up to v cc (1.65v to 5.5v) can be transmitted in ei ther direction. when the select pin is low, b 0 is connected to the output a pin. when the select pin is high, b 1 is connected to the output a pi n. the path that is open will have a high-impedance state with respect to the output. break-before-make is guaranteed. features sc-70 6-lead package 1.65v to 5.5v v cc operation 1 ? connection between ports break-before-make switching typical application aoz6135 mic pre-amp codec external mic internal mic
aoz6135 rev. 1.1 april 2010 www.aosmd.com page 2 of 11 ordering information aos green products use reduced levels of halogens, and are also rohs compliant. please visit www.aosmd.com/web/quality/rohs_compliant.jsp for additional information. pin configuration truth table part number ambient temperature range package environmental AOZ6135HI -40c to +85c sc-70-6 rohs compliant green product 1 2 3 6 5 4 b 1 gnd b 0 s vcc a sc-70-6 (top view) logic s input function 0b 0 connected to a 1b 1 connected to a
aoz6135 rev. 1.1 april 2010 www.aosmd.com page 3 of 11 absolute maximum ratings exceeding the absolute maximum ratings may damage the device. recommend operating ratings the device is not guaranteed to operate beyond the maximum operating ratings. notes: 1. signals on a, or b or s exceeding v+ will be clamped by inte rnal diodes. limit forward diode current to maximum current rati ngs. 2. negative current should not exceed minimum negative value. 3. all leads welded or soldered to pc board. 4. unused inputs must be held high or low. they may not float. symbol parameter rating v cc supply voltage -0.5v to +6v v s switch voltage (1) -0.5v to v cc v in input voltage (1) -0.5v to v cc i ik minimum input diode current (2) -50ma i sw switch current 200ma i swpeak peak switch current (pulsed at 1ms, <10% duty cycle) 400ma t stg storage temperature range -65c to +150c t j maximum junction temperature +150c p d sc-70-6 power dissipation at 85c (3) 180mw esd human body model (jesd22a-114e) 8000v symbol parameter rating v cc supply voltage 1.65v to +5.5v v in control input voltage (4) 0v to v cc v sw switch input voltage 0v to v cc t a operating temperature -40c to +85c
aoz6135 rev. 1.1 april 2010 www.aosmd.com page 4 of 11 electrical characteristics unless otherwise indicated, sp ecifications indicate a temperature range of -40c to +85c symbol parameter test conditions v cc (v) min. typ. (1) max. units dc characteristics v ih input voltage high 1.65 to 2.7 1.0 v 2.7 to 3.6 1.5 4.5 to 5.5 2.0 v il input voltage low 1.65 to 2.7 0.4 v 2.7 to 3.6 0.6 4.5 to 5.5 0.8 r on on resistance i out =100ma, b0 or b1 = 0v, 1.5v, 2.5v, 3.5v, 3.75v, 4.5v 4.5 0.6 1.2 ? i out = 100ma, b0 or b1 = 0v, 1.5v, 2v, 2.7v 2.7 1.0 1.5 i out =100ma, b0 or b1 = 0v, 1.25v, 1.5v, 1.8v 1.8 3.0 6.0 r flat on resistance flatness i out =100ma, b0 or b1 = 0v to v cc 4.5 0.2 ? 2.7 0.3 1.8 2.5 r on on resistance matching between channels i out =100ma, b0 or b1 = 1.5v 4.5 0.03 0.15 ? i out =100ma, b0 or b1 = 3.5v i in input leakage current v in = 0v or v cc 1.95 to 5.5 1.0 a i b(off) off stage switch leakage a = 1v, 4.5v, b0 or b1 = 4.5v, 1v 1.95 to 5.5 20 na i a(on) on state switch leakage a = 1v, 4.5v, b0 or b1 = 4.5v, 1v or floating 1.95 to 5.5 40 na power supply v cc power supply range 1.65 to 5.5 1.65 5.5 v i ccq quiescent supply current v in = 0v or v cc , i out = 0v 5.5 0.5 a i cct increase in i cc per input v in = 1.8v 5.5 30 40 a v in = 2.6v 18 25
aoz6135 rev. 1.1 april 2010 www.aosmd.com page 5 of 11 notes: 1. typical values are for design aid only, not guaranteed nor subject to production testing. ac characteristics t on turn-on time b 0 or b 1 = 1.5v, r l = 50 ? , c l = 35pf 2.7 to 3.6 60 65 ns 4.5 to 5.5 35 40 t off turn-off time b 0 or b 1 = 1.5v, r l = 50 ? , c l = 35pf 2.7 to 3.6 20 30 ns 4.5 to 5.5 15 20 t bbm break-before-make time 1.65 to 1.95 20 ns 2.3 to 2.7 20 3.0 to 3.65 20 4.5 to 5.5 20 q charge injection c l = 1.0nf, v ge = 0v, r gen = 0 ? 4.5 to 5.5 75 pc 2.7 to 3.6 50 analog switch characteristics oirr off isolation r l = 50 ? , f = 1mhz 2.7 to 5.5 -60 db x talk crosstalk r l = 50 ? , f = 1mhz 2.7 to 5.5 -60 db bw -3db bandwidth r l = 50 ? 2.7 to 5.5 180 mhz thd total harmonic distortion v in = 2v pk-pk , f = 20hz to 20khz 2.7 to 5.5 0.002 % capacitance c in control pin capacitance f = 1mhz, vbias = 1.5v 0.0 3.0 pf c off b port off capacitance f = 1mhz, vbias = 1.5v 4.5 7.0 pf c on a port capacitance when switch enable f = 1mhz, vbias = 1.5v 4.5 40.0 pf electrical characteristics (continued) unless otherwise indicated, sp ecifications indicate a temperature range of -40c to +85c symbol parameter test conditions v cc (v) min. typ. (1) max. units
aoz6135 rev. 1.1 april 2010 www.aosmd.com page 6 of 11 ac loading and waveforms v b v out r l c l 35pf v out r l c l 35pf 50 50 50% vcc 0.9 x v out 0.9 x v out vcc 0v control input switch output 0 t r t f = = 2.5ns t off t on v out logic input waveform are inverted for switches with opposite logic sense gnd gnd vcc v b b 0 b 1 a s gnd vcc b n a s c l includes fixture and stray capacitance c l includes fixture and stray capacitance vcc 0v v out 0.9 x v out t d t r t f = = 2.5ns control input 50% figure 2. off state leakage current figure 3. on state leakage current + + + gnd vcc b n a s + + figure 1. turn-on/turn-off timing figure 4. break-before-make timing figure 5. off isolation figure 6. crosstalk s b a 0 gnd v out 50 50 50 vcc network analyzer vcc or 0v + source signal v in s b a 1 gnd v out 50 50 50 vcc network analyzer vcc or 0v + source signal v in b 0
aoz6135 rev. 1.1 april 2010 www.aosmd.com page 7 of 11 ac loading and waveforms (continued) s v out r c l gnd gen a b 0 b 1 or v gen input control 1 capacitance meter f = 1mhz 10nf vcc v out on on off off off off in in v out vcc s 0v or vcc gnd a b 0 b or q = ( v out )(c l ) gnd vcc b n a s figure 7. on state resistance + + 600 600 gnd b n a s + audio analyzer source signal vcc c l c l includes fixture and stray capacitance figure 8. charge injection figure 9. on/off capacitance measurement figure 10. bandwidth figure 11. harmonic distortion 50 50 gnd vcc b n a s + network analyzer source signal
aoz6135 rev. 1.1 april 2010 www.aosmd.com page 8 of 11 package dimensions, sc70-6l e1 d e1 e a a2 a1 b c l e 0.15mm 0.65 0.35 1.95 0.65 .010mm gauge plane notes: 1. all dimensions are in millimeters. 2. dimensions are inclusive of plating 3. package body sizes exclude mold flash and gate burrs. mold flash at the non-lead sides should be less than 3 mils. 4. die is facing up for mold and facing down for trim/form; i.e., reverse trim/form. 5. dimension l is measured in gauge plane. 6. controlling dimension is millimeter, converted inch dimensions are not necessarily exact. symbols a a1 a2 b c d e e e1 e1 l dimensions in millimeters min. 0.00 0.7 0.15 0.08 1.85 1.80 1.1 0.26 0 nom. 0.9 2.10 2.30 0.65 bsc 1.30 bsc 1.30 0.36 4 max. 1.10 0.10 1.00 0.30 0.22 2.15 2.40 1.4 0.46 8 symbols a a1 a2 b c d e e e1 e1 l dimensions in inches min. 0.00 0.028 0.006 0.003 0.073 0.071 0.043 0.010 0 nom. 0.035 0.083 0.091 0.026 bsc 0.051 bsc 0.051 0.014 4 max. 0.043 0.004 0.039 0.012 0.009 0.085 0.094 0.055 0.018 8 unit: mm recommended land pattern
aoz6135 rev. 1.1 april 2010 www.aosmd.com page 9 of 11 tape and reel dimensions, sc70-6l carrier tape reel tape size 8mm reel size ?180 m ?180.00 0.50 package sc-70, 6l (8mm) a0 2.40 0.10 b0 2.40 0.10 k0 1.19 0.10 d0 1.00 min. d1 1.55 0.05 e 8.00 0.30 e1 1.75 0.10 e2 3.50 0.05 p0 4.00 0.10 p1 4.00 0.10 p2 2.00 0.05 t 0.25 0.05 n ?60.50 k0 unit: mm b0 g m w1 s k h n w v r trailer tape 300mm min. or 75 empty pockets components tape orientation in pocket leader tape 500mm min. or 125 empty pockets a0 p1 p2 feeding direction p0 e2 e1 e d0 t d1 w 9.00 0.30 w1 11.40 1.00 h ?13.00 +0.50/-0.20 k 10.60 s 2.00 0.50 g ?9.00 r 5.00 v 18.00 leader/trailer and orientation
aoz6135 rev. 1.1 april 2010 www.aosmd.com page 10 of 11 part marking AOZ6135HI awl a ss em b ly lot & loc a tion code p a rt n u m b er code week & ye a r code
aoz6135 rev. 1.1 april 2010 www.aosmd.com page 11 of 11 as used herein: 1. life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provid ed in the labeling, can be reasonably expected to result in a significant injury of the user. 2. a critical component in any component of a life support, device, or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. this datasheet contains preliminary data; supplementary data may be published at a later date. alpha & omega semiconductor reserves the right to make changes at any time without notice. life support policy alpha & omega semiconductor products ar e not authorized for use as critical components in life supp ort devices or systems. revision history revision revised item rev. 1.0 initial release rev. 1.1 icct max limit relaxed after production data were collected

▲Up To Search▲

Price & Availability of AOZ6135HI

	To Download AOZ6135HI Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .